[IC]：TLSR8258
[Frequency]：2.40~2.48GHz
[Power]：12dBm
[Distance]：500m
[Size]：11.5*18mm
[Introduction]：E180-Z5812SX is a ZIGBEE module designed and produced by Chengdu Ebyte based on the TELINK TLSR8258 wireless SOC. It has a small size, low power consumption, high reliability, and works in the 2.4GHz frequency band. The chip comes with a 32-bit high-performance MCU up to 48Mhz.
| Pin number | Pin name | Pin direction | Pin usage |
| 1 | NC | - | Reserved, directly suspende |
| 2 | GND | - | Ground wire, connected to power reference ground |
| 3 | NC | - | Reserved, directly suspende |
| 4 | PD3(WAKE) | Input | The WAKE pin is mainly used to wake up the dormant terminal. It is at a high level when powered on. When the pin is pulled low externally, the |
| 5 | PD7(TX) | Output | Serial sending port TX |
| 6 | PA0(RX) | Input | Serial receiving port RX |
| 7 | NC | - | Reserved, directly suspended |
| 8 | NC | - | Reserved, directly suspended |
| 9 | PD4(MODE) | Input | Working mode switching pin, when the pull-down time is greater than 500ms, the working mode is switched. |
| 10 | PA1(BAUD_R) | Input | The UART_BAUD_RESET pin is used to reset the baud rate of the device. It defaults to a high level when powered on. In any mode, if the pin is pulled down for more than 1000ms, the serial port parameters of the module will restore the default 11520 |
| 11 | PB1(ACK) | Output | The ACK pin is used to indicate the status of the last user datatransmission. The pin is pulled low before the transmission is started, and the pin is pulled high after the transmission is successful |
| 12 | PC0(GPI00) | Input/Output | GPIO input/output port 0 |
| 13 | VCC | - | Module power positive reference voltage, voltage range |
| 14 | GND | - | Ground wire, connected to power reference ground |
| 15 | PB4(GPI01) | Input/Output | GPIO input/output port 1 |
| 16 | NC | - | Reserved, directly suspended |
| 17 | NC | - | Reserved, directly suspended |
| 18 | PB5(AUX) | Output | The AUX pin indicates the current working status of the device. When the pin is low, it indicates that the device is busy, and when it is high, it indicates that the device is idle |
| 19 | NC | - | Reserved, directly suspended |
| 20 | NC | - | Reserved, directly suspended |
| 21 | PB6(ADC1) | Input | ADC detection port 1 |
| 22 | PB7(ADC2) | Input | ADC detection port 2 |
| 23 | NC | - | Reserved, directly suspended |
| 24 | NC | - | Reserved, directly suspended |
| 25 | SWCLK | Input/Output | Serial debug interface, serial line clock |
| 26 | SWDIO | Input/Output | Serial debugging interface, serial data input and output |
| 27 | PC2(PWM0) | Output | PWM output port 0 |
| 28 | PC3(PWM2) | Output | PWM output port 2 |
| 29 | PC4(PWM3) | Output | PWM output port 3 |
| 30 | PC1(LINK) | Output | The LINK pin indicates the current network status of the module, and the output high level meter has joined the network |
| 31 | NC | - | Reserved, directly suspended |
| 32 | PD2(PWM1) | Output | PWM output port 1 |
| 33 | NC | - | Reserved, directly suspended |
| 34 | NC | - | Reserved, directly suspended |
| 35 | NC | - | Reserved, directly suspended |
| 36 | GND | Input/Output | Ground wire, connected to power reference ground |
| 37 | nRESET | Input | Reset pin |